The method of open cut trench excavation has been the most common, conventional method for sewer lateral replacement or repair. This method consists of excavating a trench for manually installing every piece of pipe. This kind of sewer work is applicable to heavy root blockages, severely broken pipes, and collapsed pipes.
On average, the open trench method is costlier than trenchless sewer repair since it needs more restoration, excavation, and time to complete. Plus, open trench excavation may require the removal of street and sidewalk pavement access, which also increases the repair cost. In spite of the expenses that come with open trench excavation, there are examples where it’s the only option over trenchless sewer repair. Below, we shed light on some of the reasons why a company may have to open trench at a specific location.
When Open Trench Excavation Becomes a Necessity?
This method is used for one of the following reasons:
It’s Impossible to Pull Through a New Sewer Pipe:
This reason for open trench excavation is mainly about the mechanics in performing trenchless sewer work. In a few instances, the fastening materials around the joints of an already-present sewer line are too strong and thick – or the coupling sleeves wouldn’t break during ‘pipe pulling.’ As the couplings become trapped, the pressure pushes the couplings down the line, which stacks them up. The pulling ram begins to stall as the equipment becomes stressed by the increased tension. In extreme circumstances, fixed surfaces like concrete get broken, lifted, or even stalled below ground. Due to this reason, pulling a new pipe through becomes impossible, and the area around it needs to be manually dug up.
To Guarantee Safety in Areas Surrounded by Dangerous Utilities:
Often, the work is done in regions where there are a lot of utilities adjacent to the sewer. These utilities can consist of electric, water, fibre, and gas lines. Since the overall nature of these areas is dangerous, open trench excavation is advisable as compared to trenchless sewer repair. To ensure that no severe accidents occur underground, companies will usually dig those areas to expose the pipes.
Design and Engineering:
Finally, the design and engineering of the sewer line are what may push companies towards open trench excavation. For instance, a company may witness a pipe with a sewer line belly after it breaks to the ground to repair a particular line. In the case of sewer line bellies, open trench excavation is almost always required. During this process, the existing sewer line is removed, it’s dug a bit deeper, and the aggregate base is laid that supports the pipe for the appropriate slope and line flow.
What Should You Do in Case an Open Trench Excavation Is Required?
A qualified engineer will always be aware of when an open trench solution is the best choice for your property. They’ll be able to describe to you the ‘whys’ of it in detail and what changes you should expect. Scanprobe have been supplying CCTV drain camera systems to professionals in the drainage industry for over 30 years, and our camera systems have been developed with their feedback. So you can trust a Scanprobe drain camera to be up to the task of helping you to determine the best form of repair action. Plus, we’re the leading providers of WinCan VX drain camera, visit our website to browse our offerings!
You don’t have to be a scientist to get to appreciate the reason that CCTV has become a driving force in the realm of pipeline inspection. Robotics combined with advanced camera tech (like WinCan drain camera) is quite an innovative solution when it comes to inspecting pipelines.
Why CCTV pipeline inspection is trending?
Traditionally, a lot of guesswork was involved when it came to inspecting pipelines. However, with the advent of CCTV, examining pipelines, sewers, and drains is now quicker, affordable, and more accurate without disturbing the infrastructure. The approach offers a lot of benefits and is totally non-destructive. In a large number of industries today, CCTV pipeline inspection become a leading choice for carrying out pipeline inspection.
When pipe issues like corrosion, depreciation, foreign objects blockage, roots invasion, and sediment build-up occur in municipalities, CCTV can be used to conduct sewage and drain lines inspection. This tech can also be used by property developers to determine the status of drains and pipelines before investing in the property. In addition, oil firms can use remotely-operated CCTV cameras by mounting them on robotic crawlers to investigate very important pipelines and see if contamination or damage has occurred so that safety measures can be implemented.
CCTV pipeline inspection utilises easy-to-use software along with various durable instruments that can be used to capture top-quality videos and images. The software is loaded with a ton of features that ensures safety, offer protection for assets, and enhances productivity. All that’s required is a CCTV camera to be a connection with a computer. The camera sends images and data in real-time while storing the information that is collected for reference purposes, and an operator picks all of these. These visual inspection equipment are available in a variety of configurations. Plus, their capabilities are widespread that can match the demands of different environments like mainline sewers, tubes, condensers, turbines, engines, and pipes.
The CCTV pipeline inspection is also preferred due to its cost-effective nature. Some other reasons why people choose this cutting-edge technology are:
- No need for time-consuming excavation.
- It’s easier to proffer solutions and locate problems quickly, which assists in lowering costs while improving productivity.
- Preventive repairs can easily be implemented by using the data transmitted by the camera.
- Minor faults can easily be detected and sorted so that they don’t turn into major problems.
- CCTV pipeline inspection makes the first time identification of problems quite precise; this assists in circumventing all the costs that would’ve incurred as a result of the inaccurate diagnosis.
- The use of technology during the inspection is an absolutely non-destructive approach.
- Precision and speed are definitely a benefit.
- It is easier to pinpoint the exact location where the problem has occurred.
- The system is not difficult to operate and is totally user-friendly.
- A fully-integrated software, when integrated into the inspection process, assists in faster decision-making with the use of readily available real-time results.
- CCTV pipe inspection causes no harm to the environment and is totally environmentally-friendly.
The reasons highlighted above for the extensive use of CCTV in conducting a visual inspection in various industries clearly demonstrate that this cutting-edge technology is here to stay.
Scanprobe is a family run business since 1985, specialising in the manufacture, assembly, and design of CCTV pipeline inspection systems. Get in touch to learn more about our CCTV inspection services, WinCan VX, and WinCan drain camera.
If you’re experiencing sewer problems, you know the inconvenience that issues like these can cause. Drain failures or clogs can’t just be irritating but can be expensive to fix. Inspecting the internal surface of your plumbing pipes assists you in seeing exactly what type of damage is causing you sewer problems, also allowing you to locate exactly where the damage is to facilitate the repair process.
Here are three tips that you should take into consideration when searching for a drain camera for rent in England to make sure you invest in a diagnostic tool that meets your needs.
Tip 1: Look for a camera that can span the length of your pipes
Before renting a sewer camera from your local hardware store, finding out how long your main drainage pipe is can be quite helpful. This pipe connects the plumbing system of your home to the municipal sewer system.
You can consult the original building plans of your home to find out how long the main drainage pipe is. Then, you can use this information to rent a sewer camera with a feedline that’s long enough to run the length of the pipe. This makes sure that you’ll be able to inspect the whole pipe thoroughly to check for damage that could be contributing to the sewer problems of your home.
Tip 2: Look for a camera that has a self-levelling feature
When you’re using a sewer camera to inspect the interior surface of your plumbing pipes, it can be difficult to determine exactly what you’re looking at. When the images produced by the camera are askew or upside down, it can be almost impossible to identify damaged areas.
By investing in a proper sewer camera, which has the ability to level itself, you can ensure that all the images acquired from this camera are upright. This feature further enables you to inspect your plumbing pipes more easily for serious damage.
Tip 3: Look for a camera with a video-out connection
If you’re finding it difficult to identify whether or not your plumbing pipes have sustained damage, it can be helpful to have a professional plumber evaluate the footage that your sewer camera outputs. When renting a camera with a video-out connection, you can record the images that your camera captures onto a different video device.
This enables you to retain a record of the findings of the camera, and it also allows you to get the expert opinion of a plumber without having to pay for the plumber to conduct a different session with a sewer camera.
If you’re able to rent the right sewer camera, it would significantly assist you in fully leveraging the diagnostic tools. So, look for a camera with self-levelling abilities, a camera that can span the length of your main drain pipe, and a camera with a video-out connection to assist you in identifying sewer damage in the future.
If you’re looking for a CCTV drain camera in England, let Scanprobe know. Plus, we also offer a Mina survey in England. Please explore our website to know more or call us at +44 (0)203 253 2001 to get your queries answered instantly.
WinCan turns your data into decisions
WinCan VX transforms how you make decisions based on the rich data that inspection technologies of today capture. Imagine an integrated, single application offering you the power to manage your assets and resources in real-time.
Analyze: To understand maintenance needs, it runs queries on any combination of criteria. You can get results in the form of raw data, on a map, or in reports.
Budget: Manages inspection workflow, anticipates maintenance, makes budgetary projections, and allocation resources based on infrastructure condition.
Comply: Collects standards-compliant data for export, reporting, and analysis. WinCan supports over 50 defect catalogs, including WRc and MACP/PACP.
Decide: Extracts the actionable intelligence you need to make critical maintenance decisions.
Integrate: Interfaces with every major GIS platform and municipal databases, and connects with any inspection equipment.
Report: Uses schematic illustrations, photos, and filtered data to generate information-rich reports.
Share: Securely publishes completed inspections to the clouds, where clients can use a web browser to view them instantly.
WinCan is cloud-based and offers secure global success
New WinCan Web keeps your inspection data current, accessible, and secure on the cloud. How does this benefit you? Here’s how:
- Access: Authorized parties can access the most recent inspection data instantly using any device with a web browser.
- Competitive: To lower operating costs, large firms can offload IT functions, with small contractors delivering results with previously unavailable quality and speed.
- Scalability: Subscribers just pay for the storage they require and may increase that storage anytime.
- Security: Administrators may precisely control who accesses what information. To protect against data loss, the data center of WinCan provides the necessary hardware redundancy.
- Workflow: Supervisors may automate the assignment of inspection tasks, along with how inspection results are shared and compiled in real-time.
WinCan is designed to be scalable, to be able to grow with you
WinCan VX allows you to invest in the functionality you need today, and then add capabilities and bandwidth as future needs arise.
- Modules: These extensions to the core application allow you to add particular capabilities as needs arise.
- Subscriptions: With a subscription, you can license WinCan for a flat annual fee while gaining access to training, support, cloud storage, and every software update.
- Value bundles: These famous combinations of add-on modules and core functionality provide savings over individually bought components.
WinCan is innovative, offering you the advanced capability
WinCan is supported by the largest user base of the market, investing in the R&D necessary to offer innovation ahead of the competition. So whether it’s new analytical tools, new ways to inspect, or new support for downstream processes like rehab and cleaning, you can trust WinCan VX to lead the market.
- 3D: The 3D visualization technology of 3D allows you to build a virtual model of your infrastructure based on measurements collected during inspection.
- Competitive: The GIS implementation of WinCan VX makes it easy to manage infrastructure using maps as the front end. To create entire WinCan projects with pre-populated section data, just click and drag on a map.
- Scanning: The ScanExplorer module allows you to navigate and interpret data from the laser and side-scan inspections via its four-synchronized views.
WinCan allows you to collaborate, providing you with optimum teamwork
Teamwork and process – both are imperative for managing your wastewater collection network effectively, from cleaning and inspection to replacement, rehab, and maintenance. WinCan VX implement best practices of the industry, seamlessly coordinating your workflows and personnel. With WinCan Web instantly sharing inspection results, your decisions are always based on the most current, complete data.
What’s the wait now? Contact Scanprobe and get your WinCan drain camera instantly!